Let’s keep this real – if you’re running a modern office, you’ve probably noticed half your team is hunching over their desks, keyboard either on the wobbly desk top (too high) or crammed into a tiny under-desk nook (too low). That’s where a keyboard tray comes in, and if you’re a Staff Desk supplier like me, we get asked this all the time: “How do I actually install this without breaking my desk or my sanity?” Staff Desk

I’m gonna walk you through this step-by-step, no fancy jargon, no tools you don’t already have, and yes – I’ll throw in a few hacks we’ve picked up from thousands of office installs over the years. Let’s cut to the chase.
First, a quick note: not all desks are made equal. Some have pre-drilled holes (our standard Staff Desks come with these, fyi), some are solid wood, some are metal. That’ll change the process a little, but we’re gonna cover the most common scenarios so you can nail it.
What you’ll actually need (no fancy gear, promise)
Before we start digging, let’s round up the basics. You don’t need a pro toolkit here, just stuff most people have in a junk drawer or grab from a local hardware store for $10 max:
- A drill (cordless is easier, but a hand drill works in a pinch)
- A drill bit set: 1/8” for pilot holes, 5/16” for the mounting screws (that’s the size we include with every Staff Desk keyboard tray, so double-check those match)
- A level (we all hate a wobbly tray – this is non-negotiable)
- A Phillips-head screwdriver (drill bits fit a regular drill head, but keep a screwdriver nearby if you’re using a hand drill)
- A tape measure
- Pencil (to mark your holes – way better than guessing)
- Optional: An extra pair of hands (the tray can feel flimsy when you’re holding it, especially if it’s a big one – ask a coworker for 2 mins, it saves you from dropping it)
Step 1: Pick the perfect spot (skip this and you’ll regret it later)
This is the most important step, way more than drilling straight or tightening screws. If your tray is too high, you’ll still hunch; too low, your wrists’ll ache after 2 hours. Here’s our go-to rule for Staff Desk installs:
- The top of your keyboard tray should sit 25–28 inches from the floor. Why? That’s the standard ergonomic height for typing, and it lines up with the edge of most Staff Desk surfaces so your forearms rest comfortably.
- Next: Leave at least 3 inches of clearance between the tray and the front edge of your desk. Why? So you can pull the tray out all the way without it slamming into your legs. Pro tip: Don’t mount it so far back that you have to reach forward – you’ll end up typing with your shoulders up by your ears.
- Test this before you mark anything. Set your keyboard on the floor where you want the tray to sit, type for 5 mins, move it up or down until it feels natural. We’ve seen people mount it wrong and end up re-installing 6 months later – don’t be that person.
Step 2: Prep the desk (the boring part that prevents mistakes)
Now that you’ve nailed the spot, it’s time to mark your holes. If you’re using our Staff Desk’s pre-drilled holes, skip to the next part – but if you’re retrofitting a desk (or mounting a tray on a non-Staff Desk), let’s do this right:
- Flip the desk over (or slide it out away from the wall so you can access the underside – no need to tip it, just slide it forward on its legs)
- Line your tray up exactly where you want it. Hold it tight, then mark the two mounting holes on the underside of the desk with your pencil. Double-check the distance between the holes – most keyboard trays have a 12-inch gap between mounts, but ours are adjustable for all Staff Desk sizes, so measure twice.
- Drill pilot holes. This is key – if you skip pilot holes, you’ll split the wood or strip the metal screws. Drill a tiny 1/8” hole where each mark goes, just deep enough so the screw sits flush.
Step 3: Attach the tray (no more fumbling)
Okay, now the fun part – actually putting it on. Let’s split this into two cases because that’s what our customers deal with most:
Case A: Mounting on a Staff Desk with pre-drilled holes (our most common scenario)
Easy peasy, since we design our trays to match our desks exactly.
- Flip your desk so the underside is facing up (staff Desks are light enough for one person, but grab that extra pair of hands if you can)
- Line the keyboard tray’s mounting brackets up with the existing pre-drilled holes. We mark these clearly on all our Staff Desks, so no guessing.
- Take the screws we include with your tray (they’re long enough for most desk thicknesses, but if you have a super thick desk, just grab a longer screw from the hardware store – no extra cost, usually)
- Screw each bracket in tight with a Phillips screwdriver or drill. Don’t over-tighten – that’ll strip the hole or bend the bracket. Just until it doesn’t wiggle when you tug it.
- Test the tray by sliding it in and out. If it’s stiff, loosen the screws a tiny bit – it should glide smoothly, not slam.
Case B: Mounting on a different desk (retrofit, no pre-drilled holes)
Same steps, just add the pilot hole prep we talked about earlier. The only tip here: if your desk is metal, use a metal drill bit instead of a wood bit. If you don’t have one, just grab a $5 set at the hardware store – it’ll make a clean hole without bending the desk.
Step 4: Add the finishing touches (make it actually usable)
You’re almost done – don’t skip these small things, they make all the difference.
- Add a mouse pad: Most keyboard trays have a separate mouse area, but if yours doesn’t, just get a slim mouse pad and lay it on the tray. Don’t use a thick one – it’ll make your mouse move weird.
- Adjust the tilt: Our Staff Desk trays are fully adjustable, so you can tilt the front up a little to reduce wrist strain. Just loosen the small knob on the side, tilt it to your liking, and tighten it back. No tools needed.
- Clear a little space: Don’t load the tray up with your big office mouse, a stapler, and a notebook – keep it just for keyboard and mouse. That way, it slides easily and doesn’t sag over time.
Common mistakes we see (save yourself the hassle)
After installing thousands of trays with our Staff Desks, we’ve seen every mistake possible. Here’s the ones you can avoid:
- Mounting it too close to the front edge: If you do this, every time you pull the tray out, your legs will hit it, and it’ll scratch your desk. Leave that 3-inch clearance, I promise.
- Over-tightening screws: We’ve had people bend brackets so bad the tray won’t slide. Tight is good, but tight enough to not wiggle is perfect.
- Forgetting to test the height: A coworker of ours installed a tray at 32 inches once – he was slouching so bad he brought a pillow to his desk. Oops. Test it before you drill.
- Skipping the pilot hole: Split a $200 Staff Desk? Not worth the $1 minute it takes to drill a tiny hole.
If you’re installing this for your whole office, pro tip: Do one test install first, then adjust the rest. Everyone’s height is a little different, so your team might want slight tweaks to the tray height.
Now, if you’re looking to upgrade your office’s Staff Desks with matching keyboard trays, or you need help picking the right tray for your desk size, hit us up to connect for a procurement chat. We’ve got options for every desk, from small individual Staff Desks to large open-office setups, and we’ll make sure it’s installed right the first time.

Wait, a quick last thought: If you run into issues mid-install, don’t overthink it. Our team’s here to help, no matter if you bought a tray from us or another brand. But honestly, following these steps works for 9 out of 10 installs, so you’ll be fine.
References
School Chair Ergonomics of Computer Workstations, OSHA; Office Furniture Installation Guide, Business and Institutional Furniture Manufacturers Association; Staff Desk Ergonomic Best Practices, Commercial Office Supply Association.
Shanghai Xinmu Industrial Co., Ltd.
Address: 3rd Floor, NO.5# Building, No. 288 Rongxing Road, Songjiang District, Shanghai
E-mail: sales@xinmugroup.com
WebSite: https://www.xinmufurniture.com/