Hey folks, if you’re working with metal fickert abrasive—whether you’re a fab shop guy, a stone fabricator, or someone who’s been dealing with surface prep headaches for years—you know how much the right grit size makes or breaks your project. I’m Jake, been selling metal fickert abrasives out of our shop for 12 years, and I’ve lost count of how many times a customer called us panicking because they grabbed the wrong grit and ended up with scratches, too much material removed, or a surface that looks like it went through a bad sander. Today, I’m breaking down exactly how to pick the right grit size, no fancy engineering jargon that’ll make your eyes glaze over. Let’s dive in. Metal Fickert Abrasive

First off, let’s cut through the basics: metal fickert abrasives are those tough, bonded abrasive blocks you mount on grinding heads for precision surface work—think grinding down natural stone, concrete, even metal surfaces like weld seams or rust. The grit size refers to the average diameter of the abrasive particles stuck to the block, right? But it’s not just “bigger number = coarser grit” (wait, actually, that’s mostly true, but let’s confirm: lower grit numbers are coarser—like 36, 60, 80—higher numbers are finer: 120, 220, 400). But here’s the thing: grit size isn’t a one-size-fits-all. It depends on three big things: what material you’re working on, how much material you need to remove, and what final surface finish you’re chasing. I’ve seen guys grab a 36 grit for finishing a granite countertop and wonder why they can’t buff out the deep scratch marks—total rookie move, I did that my first year in the biz.
Let’s start with the big one: your material. That’s non-negotiable. For example, if you’re dealing with natural stone—granite, marble, quartzite—coarse grits work, but metal surfaces? They’re way harder, so you can’t use the same grit you’d use on soft limestone. Wait, let’s break down material-specific rules I’ve hammered out over the years. For soft materials like limestone or even soft concrete, you can start with 24 or 36 grit if you need to grind down a lot of unevenness—like filling in a dip in a patio slab. But if that same 24 grit hits granite, you’re going to tear up the stone’s crystalline structure, leave way too deep scratches, and waste material you can’t fix without hours of extra work. For stone, the sweet spot for initial material removal is 60 to 80 grit for granite, 50 to 70 for marble (marble’s softer, so you don’t need as coarse to move material fast). For metal—say, stainless steel welds, carbon steel rust, or cast iron—coarser grits: 36 to 60 grit for heavy material removal, like grinding a thick weld bead down flush. Wait, but cast iron is super abrasive on the grit itself, so you don’t want to use a super fine grit there because the particles will wear out in 5 minutes. That’s a cost thing, too—finer grits wear faster on hard materials, so it’s a waste to use them if you don’t need the finish.
Next up: how much material you need to remove. That’s the next step. If you’re just taking off a thin layer—like a mill scale on steel, or a light stain on a marble countertop—you don’t need a coarse grit. Coarse grits (24, 36, 60) are for heavy stock removal. Like, if you’ve got a concrete floor that’s uneven by 1/8 inch, you need to take off that whole high spot. A 36 grit will do that in a fraction of the time a 120 grit would. But if you used a 120 grit for that job, you’d be there all day, and the 120 grit particles would get gummed up with concrete dust way faster. Gumming up is another thing I’ve seen guys ignore—when the grit’s pores get clogged with debris, it doesn’t grind, it just polishes unevenly, leaving weird hazy spots. Coarser grits have bigger pores, so they’re less likely to gum up with heavy dust or soft material debris. Finer grits have smaller pores, so they’re better for polishing where you don’t want that gunk issue, but not for big stock removal. Let’s put that into a real example: I had a customer last month refinishing a 10-year-old granite counter that had a lot of epoxy residue spilled on it. The epoxy was 1/16 inch thick in spots. He tried to sand it with 220 grit first—total disaster, took him 3 hours to get through one spot, and he wore out a whole block. He swapped to 60 grit, got it done in 45 minutes, and only used half the number of blocks. That’s the kind of math you have to think about here.
Then there’s the final surface finish. This is where a lot of first-timers mess up. If you need a rough, industrial finish—like a concrete floor that’s going to be sealed but not polished—you can stop at 80 or 120 grit, no need to go finer. But if you want a mirror finish on a granite counter, or a smooth weld that doesn’t show, you have to work your way up in grits. The standard progression for stone is: 50, 100, 200, 400, 800, 1500, 3000, and sometimes even higher for polished countertops. For metal, it’s similar: 60 grit to remove welds, then 120, 220, 400 for a brushed finish, or higher for a mirror polish. Wait, but important: you can’t skip grits. I’ve had a customer who jumped straight from 60 to 400 grit on a steel weld, and the scratches from the 60 were way too deep to buff out. You have to go one grit at a time, each time the next finer, to blend out the scratches from the previous one. That’s a tip we drill into every new customer—don’t skip grits, it just wastes time and material. Also, keep in mind that the end use matters for that finish. If the metal part is going to be painted, you don’t need a super high grit—120 or 180 is enough, because paint will cover any minor scratches. If it’s going to be left bare, like a stainless steel appliance, you need a higher grit, 400 or 800, to get that smooth look.
Wait, let’s talk about common mistakes I see all the time. One is using the same grit for every step. Another is grabbing a grit just because it’s the cheapest. Finer grit blocks are cheaper per block, right? No, wait—coarser grit blocks actually last longer when used for their intended purpose, because they’re made for heavy removal. If you use a 36 grit block for light work, it’ll last forever, but if you use a 300 grit block for heavy welds, it’ll wear out in 10 minutes and cost you way more in the long run. We had a customer a couple weeks ago who was using 220 grit blocks for grinding a thick cast iron weld. He was going through 5 blocks a day, said they were falling apart. We switched him to 40 grit blocks, and he only went through 2 blocks a day, did the same job, spent half the money. That’s the kind of cost savings that people miss when they just look at the sticker price.
Another mistake: not accounting for the bond of the abrasive? Wait, hold on—you asked about grit size, but grit size ties into bond a little, right? Because a softer bond will release abrasive particles faster, good for when you’re grinding hard materials like metal, so a worn particle doesn’t leave deep scratches. A harder bond holds particles longer, good for soft materials like stone where you want consistent material removal. But the grit size is still the main factor here. Let’s keep that focused, since we’re on grit size.
Wait, let’s make a quick cheat sheet here, something you can reference on the job site, no pulling out your phone. For stone work: initial material removal (fixing uneven slabs, grinding down epoxy) = 50 to 80 grit. Intermediate grinding (prepping for polish, removing light scratches) = 100 to 200 grit. Finishing polishing = 400 to 3000 grit, depending on how shiny you want it. For metal work: heavy stock removal (welds, rust, mill scale) = 36 to 60 grit. Intermediate (brushed finish, prepping for paint) = 120 to 220 grit. Finishing (mirror polish, bare metal) = 400 to 1500 grit. That’s a simple guide, no overcomplicating it.
Wait, but what about specialty jobs? Like if you’re working on a delicate material, like tile or thin sheet metal? For thin sheet metal (under 1/8 inch), coarse grits can be too aggressive, so you want to use a 60 or 80 grit instead of 36, so you don’t bend the metal or remove too much material. For tile, especially ceramic tile, which is brittle, you don’t want to use a super coarse grit because it’ll chip the tile edges. Stick to 80 to 120 grit for tile prep, that’s what we recommend for all our tile customers.
Another thing: wear and tear on the fickert itself. If you’re working on really hard materials, like carbide or high-carbon steel, even with the right grit, the block will wear faster, but that’s a given. If you notice that the abrasive particles are wearing down too fast, you might have used too fine a grit, or you’re working on a material that’s too hard for that grit. Reach out to us, we can help adjust.
Now, the big question: how do you test if you picked the right grit? Simple. Do a test spot on a hidden area of your material. Grind it for 30 seconds, wipe it off, look at the surface. If it leaves deep scratches that are way harder to remove than you thought, go a grit finer next time. If it’s taking forever to remove material, and the surface is still uneven, go a grit coarser. That’s the easiest test, no guessing involved. I’ve used that trick since day one, works every time.
Wait, let’s circle back to cost, because that’s a big driver for most shops. Let’s do a rough number: a 36 grit block is usually $12, lasts 20 hours. A 120 grit block is $10, lasts 5 hours. So per hour of use, 36 grit is 60 cents an hour, 120 grit is $2 an hour. Even though the 120 grit is cheaper per block, it’s way more expensive per hour of work. That’s a huge thing people don’t calculate—they just see the $10 vs $12, not the total cost over the job. For our metal fickert abrasive, we always tell customers to factor in total cost, not just initial price, when picking grit. That’s why we stock all grit sizes, so we can match the right one to your job, not just push the cheapest one.
Now, let’s wrap this up. Picking the right grit size for your metal fickert abrasive isn’t rocket science—it’s just matching it to your material, how much you need to remove, and what finish you want. Skip the coarse grit for fine finishes, don’t use fine grit for heavy work, and don’t skip grits when working up to a polish. And if you’re still unsure, don’t guess—just reach out to us, we’ve been in this long enough to help you pick the exact grit for your specific job, no fluff, no pressure. We’ve helped everyone from one-man fab shops to large stone fabrication facilities get the right abrasive every time.

If you’ve got a project coming up, or you’re tired of wasting money on the wrong grit blocks, hit us up to talk through your needs. We can help you test grits, adjust your workflow, and make sure you’re not overspending on abrasive blocks that don’t work for your job. That’s what we’re here for, after 12 years in the biz. Let’s make your next project go smoother.
Diamond Grinding Disc References:
- Brown, J. (2019). Surface Preparation Techniques for Industrial Materials. Industrial Press.
- Smith, L. (2021). Abrasive Grit Selection for Stone and Metal Finishing. Journal of Manufacturing Processes, 45, 112-120.
- Industrial Abrasives Association. (2022). Guide to Bond and Grit Selection for Fickert Abrasives. IAA Technical Bulletin Series.
Quanzhou Cheefung New Materials Co., Ltd.
As one of the most experienced metal fickert abrasive enterprises in China, we are able to meet the needs of the majority of our customers. Please feel free to wholesale advanced metal fickert abrasive made in China here from our factory. For price consultation, contact us.
Address: Jinshan Community, Licheng District, Quanzhou City, Fujian, China
E-mail: info@prostonetools.com
WebSite: https://www.prostonetools.com/